hvac course, hvac training, hvac institute, mep course, mep institute, mep training, hvac training in bangalore, hvac institute in bangalore, hvac course in bangalore, mumbai, chennai, Trichy, Vizag, Hyderabd, pune, Gujarat, delhi branches....
mep COURSE IN bangalore | mep TRAINING IN bangalore | mep INSTITUTE IN bangalore | mep TRAINING INSTITUTES IN bangalore | mep TRAINING AND CERTIFICATION IN bangalore | mep TRAINING AND COACHING CENTER IN bangalore | mep TRAINING CENTER IN bangalore | mep IN bangalore
MEP TRAINING AND CERTIFICATION
MEP - COURSE IN BANGALORE- KARNATAKA,CHENNAI, TRICHY, COIMBATORE, MUMBAI, COCHIN
1. Heating Ventilation and Air Conditioning (HVAC)
2. Electrical Design and Drafting
3. Plumbing Design and Drafting
4. Fire Fighting and Drafting
5. Revit MEP
HEATING VENTILATION & AIR CONDITIONING
BASICS OF HVAC
- INTRODUCTION , SCOPE & USE OF AIR CONDITIONING
- CLASSIFICATION OF AIR CONDITIONING
- VENTILATION
- PSYCHROMETRIC CHART & PROCESS
- SURVEY OF BUILDING
- LOAD CALCULATION - COOLING & HEAT
DUCT DESING
- SELECTION OF INDOOR / OUTDOOR UNITS
- AIR TERMINAL SYSTEM
- AIR DISTRIBUTION SYSTEM
- DUCT DESIGN CALCULATION - USING Mc -QUAY + AUTOCAD
PIPE DESIGN
- CHILLED WATER SCHEMATIC SYSTEM
- CHILLERS & VALVES
- CHILLED WATER PUMPS
PROJECT
- ESTIMATION OF REQUIRED MATERIALS
- BILL OF QUANTITY
- DUCT QUANTITY TAKE OFF METHODS
- SPECIFICATION OF HVAC
- COOLING TOWERS & ITS TYPES
- SUPPORT & ACCESSORIES IN HVAC
- STATIC CALCULATION
- TESTING & COMMISSIONING
SOFTWARES
- AUTOCAD - 2D (DUCT & PIPE DESINING)
- REVIT - 3D (DUCT & PIPE DESINING)
- PROJECT
B. ELECTRICAL DESIGNING & DRAFTING SYLLABUS
1.GENERAL CONCEPT :
- Electrical Generation, Transmission and Distribution
- Different types of equipment and their load as per standard specifications
- Services : Lighting, Power, Fire Alarm, Emergency Lighting, etc
2.SYMBOLS AND LEGENDS :
- Power Services
- Lighting
- Fire Detection
- ELV/ Low Current
- Earthing and Lighting
3.POWER SERVICES :
- Cables
- Selection, Conductor, Strands, Cores and Insulation
- Armored and Unarmored Cables
- Cable tray raceway, Trunking, Conduits and Routing
- Busbar Details and selection of high rise building
- Switch Gears (Circuit Breakers) Types and Selection
- Capacitor bank (Power factor improvement)
- Panel Boards (MDB, SMDB, SDB, etc)
- Single line Diagram (SLD)
- Calculation: Voltage drop calculation and load calculation based on BS 7671
4.LIGHTING :
- Lux level design as per BS 12464
- Escape route lighting as per NFPA 101
- Different types of Lamp like GSL, ETL, CFL, LED, MVL, etc
5.FIRE DETECTION :
- Fire alarm system as per NFPA 72
- Smoke (Heat Detection)
- Sounders & Manual call points
- Voice evacuation system for commercial / Residential building
6.ELV / Low Current system: (General Concepts) :
- Public Address System
- Close circuit television (CCTV): Types of cameras and circuiting
- Communication: TV, Telephone, intercom and internet networking of cables and types
7.Earthing and Lighting :
- Lighting Protection
- Introduction to Lightning Arresters
- Lightning protection system design based on BS/IEC 62305
- Types of Earthing According to the requirements
- Earthing system design in line with BS 7430
8.TYPES 0F DRAWING: DESIGN DRAWING AND SHOP DRAWING :
9.DRAWING DETAILS :
- Lighting Layout
- Power Layout
- Emergency Lighting Layout
- CCTV Layout
- Public Addressable Layout
- Fire Alarm system Layout
- Communication Layout
- Cable Tray Layout
- BUSBAR Layout
- Bus duct riser drawings
- Single line drawing (SLD)
10.STANDARD & CODES :
- Designing as per Electrical standards: DEWA, ADEWA, ADDC, KHARAMA, etc
11.PROJECT :
- Lighting Layout
- Power Layout
- Single line drawing (SLD)
- FA, PAVA, Emergency Lighting Layout
- Communication layout
- ELV system (CCTV, ACS, etc)
C. PLUMBING DESIGNING SYLLABUS
CERTIFICATE IN PLUMBING DESIGNING
For students and professionals who need to add plumbing expertise to their engineering credentials, this certificate provides a through introduction to every aspect of plumbing systems design.
COURSE DESCRIPTION:
PLUMBING SYSTEM DESIGN - LEVEL 01
Learn the fundamentals of pressurized water distribution systems for commercial and residential high - rise buildings, Topics include pressure flow equations, friction, mechanical pumping, cold water distribution, backflow prevention, applicable codes and their use, and system selection.
PLUMBING SYSTEM DESIGN - LEVEL 02
Understand the fundamentals of sanitary and storm drainage system design for commercial and residential high - rise building. This course includes coverage of laboratory healthcare acid waste and drainage systems: piping materials: hangers and storm flow: venting: indirect waste: laboratory waste: piping materials: hangers and supports for drainage piping: ejector and sump pump design: site drainage design: storm water detention systems: grease, oil, and sediment interceptors: and acid waste neutralization. Gain an overview of advanced technologies related to sanitary and storm water system, such as grey water and black water system and storm water reuse systems and filtration.
AFTER COMPLETION OF THE PROGRAM, STUDENTS ARE SKILLED IN THE FOLLOWING AREAS
- Pressurized water distribution systems
- Water chemistry and treatment
- Hot and cold water distribution
- Valves and fixture
- Nature gas distribution
- Building drainage system
- Storm water drainage
- Sanitary waste disposal
This certificate is awarded to students after successful completion of the training
For further details contact us immediately.
D. FIRE FIGHTING SYLLABUS
FIRE FIGHTING COURSE PLAN
1.BASISCS OF FIRE FIGHTING :
- Basics of fire fighting
- Fire fighting standards
- Fire fighting pipe materials
- Fire legends
2.EXPLANATIONS OF NFPA CODES :
- Overview of NFPA 10
- Overview of NFPA 13
- Overview of NFPA 14
- Overview of NFPA 20
- Overview of NFPA 22
3.FIRE PROTECTION SYSTEM :
- Active fire protection system
- Passive fire protection system
4.CLASSIFICATION OF FIRE :
- Classification of occupancies
- Classification of commodity
5.DESCRIPTION OF FIRE HAZARDS :
- Description of fire hazards
- Classification of hazards
- Detailed explanation of hazards
6.TYPES OF SPRINKLER SYSTEM :
- Types of sprinkler system
- Explanation of Wet sprinkler system
- Explanation of Dry sprinkler system
- Explanation of Pre - Action sprinkler system
- Explanation of Automatic sprinkler system
7.DESCRIPTION OF SPRINKLER AND HOSE SYSTEM :
- Sprinkler system explanation
- Types of sprinkler
- Selection of sprinkler
- Hose reel system
8.FIRE EXITNGUSHERS DETAILS AND ARRANGEMENTS :
- Types of extinguishers
- Arrangements of fire extinguishers
- Applications of fire extinguishers
9.DETAILS & DESIGN OF ZONE CONTROL VALVE :
- Description of zone control valve
- Design of zone control valve
10.FIRE FIGHTING DESIGN CRITERIA :
- Sprinkler design
- Sprinkler arrangements
- Pipe sizes
11.DESIGN OF FIRE SUPPRESSION SYSTEM :
- Design of fire suppression system
12.EXTERNAL FIRE FIGHTING DESIGN :
- Design of Fire Hydrants
- Design of Breaching Inlet
13.DESCRIPTION OF FIRE PUMPS :
- Detailed description of fire pumps
- Types of pump
14.FIRE PUMP ROOM DETAIL :
- Fire pump installation details
- Fire equipments design
- Fire pump rooms line sketch
- Pipe and equipments support details
15.FIRE PUMP CALCULATION :
16.FIRE FIGHTING HYDRAULIC CALCULATION :
17.FIRE FIGHTING TECHNIQUIES :
- Site photos presentation
- Establishments of new creativities
- Fire Fighting techniques
18.DESCRIPTION OF FIRE FIGHTING LAYOUTS :
- Detail description of design drawings
- Detail description of shop drawings
19.LAYOUT PREPARATION PROCEDURES :
- Design drawing preparation procedures
- Shop drawing preparation procedures
20.GENERAL DRAWING PREPARATION PROCEDURES :
- Schematic drawing preparation procedures
- Shop drawing preparation procedures
- Sectional layouts preparations
- Bill of Quantity preparations
21.PROJECT :
- Commercial Building Fire Fighting Design
- Residential Building Fire Fighting Design
- Airport Fire Fighting Design
- Hospital Building Fire Fighting Design
E. REVIT MEP SYLLABUS
- Building information Modeling
- Building information Modeling(BIM)
- Revit MEP Basics Overview of the interface
- Standard Terminology
- Starting Projects
- Viewing Commands Basics Drawing & Editing Tools
- General Drawing Tools
- Editing Elements
- Standard Modifying Tools
- Helpful Editing Tools
- Starting MEP Projects
- Linking in Architectural Projects
- Introduction to Architecture
- Copying & Monitoring Objects
- Setting Up Levels
- Working with Views
- Duplicating Views
- Adding Callout Views
- Setting The View Display
- Creating Elevations
- Creating Sections
- Working With Ceilings
- Understanding Revit
- MEP Systems
- Working with Schedules
- Creating Schedules
- Working with Dimensions
- Working with Text
- Adding Detail Lines & Symbols
- Creating Legends
- Tag & Schedules
- Adding Tags
- Detailing in Autodesk
- About MEP Systems
- HVAC Systems
- About HVAC System
- Adding Air Terminals & Mechanical Equipment
- Adding Ductwork
- Creating Duct Systems
- Automatic Ductwork Layouts
Practice
- Working With Components
- Creating Systems - Overview
- System Graphics
- Connecting Components
- Analyzing Systems
- Spaces and Zones
- Creating Spaces
- Working with Spaces
- Creating Zones
- Creating Color Schemes
- Performance Analysis
- Preparing a Project for Energy Analysis
- Analyzing the Heating & Cooling Loads
PIPING SYSTEM
- Hydronic Piping
- Systems
- About Hydronic Piping Systems
- Adding Mechanical Equipment
- Drawing Piping
- Creating Hydronic System
- Automatic Piping Layouts
- Visibility Graphic
- Creation Of Pipes
- Practice
- Fire Production Systems
- Plumbing Systems
- About Plumbing Systems
- Adding Plumbing Fixtures
- Drawing Piping For Plumbing Systems
- Working With Plumbing Systems
- Electrical system
- About Electrical system
- Placing Electrical components
- Creating Electrical circuits
- Cable trays and conduit
- Electrical panel Schedules
- Family creation
- Family creation
LAYOUTS
TOPICS :
- Construction documents phase
- Construction
- Documents
- Setting up sheets
- Placing & modifying views on sheets
- Adding revisions
- Printing sheets
- Work sharing
